ASTM D3161
A wind resistance test for shingles from ASTM International using a fan-induced airflow. Results are listed as Class A (60 mph), Class D (90 mph), or Class F (110 mph).
The complete reference guide for residential and commercial roofing terminology. Search, explore, understand.
This roofing glossary brings together over 180 roofing terms and definitions used daily by contractors, estimators, crew leads, and sales reps. It covers roof styles, installation methods, codes and ratings, and the insurance and business vocabulary behind every job. Use it in the field, during training, or when a homeowner asks what a drip edge is.
A wind resistance test for shingles from ASTM International using a fan-induced airflow. Results are listed as Class A (60 mph), Class D (90 mph), or Class F (110 mph).
An ASTM wind uplift test for shingles that measures the sealant bond. Results are listed as Class D (90 mph), Class G (120 mph), or Class H (150 mph). Often required in high-wind coastal markets.
Official approval from the local building department to perform roofing work. Most jurisdictions require permits for full replacements. Some also require them for larger repairs. Permits trigger inspections and code compliance checks.
The highest hail resistance rating under UL 2218, a standard from UL. To pass, a roofing product must withstand a 2-inch steel ball dropped from 20 feet onto the same spot twice without cracking. Can qualify homeowners for insurance discounts in some states.
The Cool Roof Rating Council is a nonprofit that independently rates roofing products for solar reflectance and thermal emittance. CRRC ratings are referenced in energy codes and green building programs.
A classification of a roof assembly's fire resistance under ASTM E108 or UL 790. Class A is the highest rating, followed by Class B and Class C. Most asphalt shingles, tile, slate, and metal achieve Class A.
Florida's statewide building code maintained by the Florida Building Commission under Chapter 553, Florida Statutes. It supersedes local building codes, though local governments can adopt limited amendments. Contractors must hold the appropriate Florida roofing license to work under it.
Product testing and certification from FM Approvals, focused on fire, wind, and hail performance of commercial roof assemblies. Often required by commercial building insurers.
A construction standard from the Insurance Institute for Business & Home Safety (IBHS) that strengthens roofs against wind and water intrusion with sealed decks, ring-shank nails, and upgraded edge details. Some states offer insurance discounts or grants for FORTIFIED-certified roofs.
The region of Florida covering Miami-Dade and Broward counties, where the Florida Building Code imposes its most stringent roofing requirements. Products installed here generally need specific approvals such as a Miami-Dade NOA.
The model code published by the International Code Council that governs commercial and larger residential buildings. Adopted and amended by most U.S. states and local jurisdictions.
The ICC model code for one- and two-family homes and townhouses, viewable free through ICC's digital codes library. Chapter 9 covers roof assemblies, including underlayment, ice barriers, drip edge, flashing, and reroofing rules. Local adoption and amendments vary.
A credential from a roofing manufacturer recognizing a contractor's training, licensing, insurance, and track record. Examples include GAF Master Elite, Owens Corning Platinum Preferred, and CertainTeed ShingleMaster. Certified contractors can often offer extended system warranties.
A Notice of Acceptance issued by Miami-Dade County after a roofing product passes the county's testing protocols. Required for products installed in the HVHZ and often treated as a gold standard for wind performance elsewhere.
The National Roofing Contractors Association (NRCA) is the largest U.S. trade association for roofing professionals. Publishes technical manuals, offers training and certification, and is a regular presence at the major roofing trade shows.
Federal rules requiring fall protection for construction workers at heights of 6 feet or more, including residential roofing. Options include guardrails, safety nets, and personal fall arrest systems.
State or local authorization to perform roofing work. Requirements range from no state license to exams, experience minimums, bonding, and insurance. Check the state-by-state roofing license requirements before bidding work.
A single value that combines a surface's solar reflectance and thermal emittance to show how well it stays cool in the sun. Higher SRI means a cooler roof. Used in cool roof codes and LEED credits.
Dark streaks on shingles caused by algae, most often Gloeocapsa magma. Mostly cosmetic but frequently mistaken for damage or dirt. Many shingles now include copper-infused granules that resist algae.
A cracked pattern resembling alligator skin on aged asphalt, coatings, or built-up roofs. Caused by UV exposure and loss of oils. Signals the surface is near the end of its service life.
Raised bubbles in shingles or membranes caused by trapped moisture or gas expanding under heat. Small blisters on shingles may be cosmetic. Blisters on low-slope membranes often point to moisture in the system.
A small sample cut from a low-slope roof to reveal the number of layers, insulation type, and moisture. Used for commercial inspections and replacement scoping. The cut must be patched immediately.
Shingle edges that turn upward (cupping) or tabs that curl down at the corners (clawing). Usually caused by age, heat, or poor ventilation. Curled shingles blow off more easily and let water in.
A roof inspection performed with a camera drone. Safer and faster on steep or fragile roofs, this produces images homeowners and adjusters can see. Commercial drone pilots need FAA Part 107 certification.
A tarp secured over a damaged section to stop water intrusion until permanent repairs can be made. Often the first service a contractor provides for a roofing emergency call.
The shedding of mineral granules from asphalt shingles, exposing the asphalt beneath to UV damage. Some loss is normal on new roofs. Heavy loss, bald spots, or granules piling in gutters signal aging or hail impact.
Impact damage to roofing from hailstones. On asphalt shingles, look for soft bruises, fractured mats, and granule loss at the strike point. On metal, look for dents. Collateral damage to gutters, vents, and siding helps document a claim. IBHS publishes ongoing research on how roofing materials hold up to hail.
An inspection using a thermal camera to find trapped moisture beneath a low-slope roof surface. Wet insulation holds heat differently than dry, so it shows up after sunset. Usually confirmed with core cuts.
The process of tracing water intrusion back to its source. Water often travels along rafters or decking before showing up on a ceiling, so the stain is rarely directly below the leak.
Plant growth that takes hold on shaded, damp roofs. Moss lifts shingles and holds moisture against the surface. Remove with gentle cleaning methods, since pressure washing strips granules.
A nail that has backed out of the decking, lifting the shingle above it. Caused by deck movement, poor nailing, or temperature swings. Can puncture the shingle above and create a leak.
Water that stands on a flat or low-slope roof long after rain stops, often defined as more than 48 hours. Accelerates membrane breakdown and adds structural load. Many manufacturers exclude ponding damage from warranties.
The core decision in most roofing consultations. Repairs make sense for isolated damage on a roof with plenty of life left. Replacement makes sense when damage is widespread, the roof is near the end of its lifespan, or repair costs approach a large share of a new roof.
A systematic evaluation of a roof's condition, covering the surface, flashing, penetrations, gutters, ventilation, and attic. Usually the first step before any repair, replacement, or claim.
Routine care that extends roof life: clearing debris, checking flashing and sealants, cleaning gutters, and replacing damaged pieces early. A seasonal roof maintenance checklist can help build recurring service plans that keep your schedule steady year-round.
A visible dip or wave in the roof plane, usually caused by rotted decking, overloaded framing, or failed structural members. A structural concern that needs evaluation before any roofing work proceeds.
A 10-by-10-foot area marked on a roof slope by an adjuster or inspector to count hail hits. Many insurers use a threshold number of hits per test square to decide whether a slope qualifies for replacement. Thresholds vary by carrier.
Damage caused by high winds: lifted, creased, torn, or missing shingles, loose flashing, and debris impact. Creased shingles may look intact from the ground but have lost their seal.
A low-slope membrane held in place by the weight of river rock or concrete pavers instead of fasteners or adhesive. Fast to install but adds significant load and isn't suited to high-wind areas.
Fasteners with a wide plastic or metal cap, used to secure underlayment. The cap spreads the holding force and reduces tear-through in wind.
A valley technique where shingles from one roof plane run through the valley and shingles from the other plane are cut along a chalk line above it. The most common residential valley method. Clean look, but the cut line must be done precisely.
The point when the roof is sealed against weather with underlayment, even if the final covering isn't installed. A key milestone when weather threatens mid-job.
The portion of each shingle left visible after the next course is installed. Commonly about 5 to 5 5/8 inches for asphalt shingles, depending on the product. Wrong exposure throws off the whole layout and can void the warranty.
A low-slope membrane bonded to the substrate across its entire surface with adhesive. Strong wind performance and no fastener penetrations through the membrane.
Applying dabs of roofing cement under shingle tabs by hand. Used in cold weather when the factory sealant strips won't activate or on steep slopes and high-wind areas where manufacturers require it.
The distance one shingle overlaps the shingle two courses below it. Headlap is what keeps water out at the nail line.
Joining thermoplastic membrane seams (TPO or PVC) with a hot-air welder that fuses the sheets together. A proper weld is stronger than the membrane itself.
Driving nails above the manufacturer's nailing zone. High nails can miss the underlying shingle, cutting wind resistance and causing shingles to slide or blow off. A common cause of denied warranty claims.
A low-slope membrane secured to the deck with fasteners and plates along the seams. Fast to install and lightweight. Fastener patterns are set by the wind zone and manufacturer specs.
The marked strip on a shingle where nails must go, usually indicated by a painted line or reinforced band. Standard installs use four nails per shingle. High-wind installs typically use six.
The horizontal stagger between joints in successive shingle courses, so seams never line up vertically. Each manufacturer specifies a minimum offset.
A valley where shingles are trimmed back on both sides, leaving a strip of exposed metal flashing down the center. Handles heavy water flow well and is common with tile, slate, and metal roofs.
Installing new shingles over an existing layer instead of tearing off. Also called a layover or recover. Saves labor but hides deck problems, adds weight, and may shorten the new roof's life. The IRC generally prohibits an overlay when two or more layers already exist.
Installing shingles straight up the roof in vertical columns instead of the stepped diagonal pattern. Faster, but most manufacturers advise against it because it can produce uneven shading and alignment problems.
A nail with ridges along the shank that grip the decking better than smooth-shank nails. Often required for decking attachment in high-wind zones.
The first row of material installed along the eaves and rakes, beneath the first shingle course. Provides a sealant line that holds the first course down and blocks water at the edge.
Removing the existing roof down to the decking before installing a new roof. This lets the crew inspect and replace damaged decking. Requires a dumpster, ground protection, and magnet sweeps for nails.
An installation method for modified bitumen where an open propane torch melts the back of the sheet to bond it. Effective but a fire risk, and some insurers and jurisdictions restrict it.
A valley technique where shingles from both roof planes are interlaced across the valley. Durable and fast with three-tab shingles, but not recommended for thicker architectural shingles.
An insurance payout based on the roof's replacement cost minus depreciation for age and wear. ACV policies often leave homeowners with a large gap between the check and the cost of a new roof. The NAIC publishes consumer guidance on how ACV and replacement cost policies differ.
The insurance company's representative who inspects roofing damage and determines what the policy covers.
An agreement where a homeowner transfers insurance claim rights to a contractor, who then deals with the insurer directly. Rules vary by state. Under Florida Statute § 627.7152, AOBs are banned for residential and commercial property policies issued or renewed on or after January 1, 2023. The Florida Office of Insurance Regulation tracks current rules.
The average value of closed jobs. Raising average ticket size through upgrades like Class 4 shingles, better ventilation, or gutter replacement is one of the fastest ways to grow revenue without more leads.
Door-to-door lead generation, common after storms in insurance restoration markets. Many municipalities require solicitor permits for this roofing marketing technique.
A document proving a contractor carries general liability, workers' compensation, and other required coverage. Homeowners, property managers, and general contractors often request one before work starts. Getting coverage in place is an early step when you start a roofing company.
The amount the homeowner pays out of pocket before insurance covers the rest. Many policies in storm-prone states use separate wind or hail deductibles calculated as a percentage of the home's insured value, which can mean thousands of dollars on a roof claim.
The reduction in a roof's insured value due to age and condition. On replacement cost policies, the withheld portion is often recoverable once the work is complete and the final invoice is submitted to the insurer.
A roofing business model built around storm damage claims, where most jobs are paid largely through homeowners insurance. Requires deep knowledge of claims, supplements, and adjuster relationships. Contractor financing can help bridge the gap between when homeowners need the work done and when they receive their insurance payout.
A document where a contractor, subcontractor, or supplier gives up lien rights after being paid. Conditional waivers take effect once payment clears. Unconditional waivers take effect immediately.
The roofing manufacturer's guarantee against material defects. Enhanced system warranties may also cover workmanship and usually require a certified installer and the manufacturer's full component system.
A legal claim against a property filed by a contractor or supplier who wasn't paid for work or materials. Rules, notice requirements, and deadlines vary by state and must be followed exactly.
An insurance endorsement that pays for code upgrades required during repair or replacement, such as adding drip edge, ice barrier, or new decking to meet current code. Not all policies include it.
A line item in insurance estimates that covers a general contractor's overhead and profit, commonly calculated as 10% each. Typically applies when a job requires coordinating multiple trades, though carrier practices vary.
A licensed claims professional hired by the policyholder, not the insurer, to negotiate a claim. Usually paid a percentage of the settlement. Licensing and fee caps vary by state. The National Association of Public Insurance Adjusters maintains a member directory and code of ethics.
An insurance payout based on the full cost to replace the roof with similar materials at current prices, without deducting depreciation. Often paid in two parts: ACV upfront and recoverable depreciation after completion.
Roofing work paid directly by the homeowner rather than through an insurance claim. Because the homeowner covers the full cost, retail jobs often depend on clear pricing, strong sales conversations, and payment options.
Payment plans offered through the roofing contractor so homeowners can spread the cost of a repair or replacement over time. Roofing financing is especially useful on retail jobs and on claims where the deductible or ACV gap leaves a large out-of-pocket balance.
A contractor who travels into areas after major storms to sell claim-funded roof replacements. Some are legitimate, but the term usually refers to operators who leave homeowners without warranty support. The National Insurance Crime Bureau warns homeowners about post-disaster contractor fraud. Local licensing helps separate established roofers from fly-by-night crews.
A request to the insurance company for additional funds when the original estimate missed items, such as drip edge, starter strip, code upgrades, or extra layers. Supported with photos, measurements, and code citations.
The contractor's own guarantee covering installation errors for a set period. Terms vary widely, from one year to the life of the roof. A key differentiator in sales conversations.
Estimating software from Verisk used by most insurance carriers and many restoration contractors to price claims line by line. Aligning your estimate format to Xactimate line items makes supplements easier to approve.
A roof measurement generated from satellite or aerial imagery, listing squares, pitches, ridge, hip, valley, and eave lengths. This allows contractors to quote jobs without climbing the roof first. Accuracy can drop with heavy tree cover or very complex roofs.
A wrapped package of shingles. For most asphalt shingles, three bundles cover one square, though some heavier products need four. Always check the wrapper.
A written document that modifies the original contract's scope or price, signed by both parties. Rotted decking, hidden layers, and code upgrades are the classic roofing change orders. Get them signed before doing the work.
A contractor's projected cost for a roofing job, broken down by materials, labor, disposal, and extras. Some contractors use "quote" for a fixed price and "estimate" for an approximation, so define your terms in the contract.
The cost of crew labor per square or per hour, including wages, burden (payroll taxes, workers' comp, benefits), and overhead. How much roofers make varies by state and experience level.
A straight-line measurement of one foot, used for edge components like drip edge, ridge cap, gutters, and flashing.
The steepness of a roof. In field usage, pitch is expressed as inches of rise per 12 inches of horizontal run. A 6:12 pitch rises 6 inches for every 12 inches across. Pitch drives material choice, waste, labor cost, and safety requirements.
A roofing tool used to measure roof pitch, either a mechanical gauge or a smartphone app.
A factor used to convert a roof's flat footprint into its actual sloped surface area. A 4:12 roof uses about 1.054, a 6:12 about 1.118, and a 12:12 about 1.414. Multiply the footprint by the factor to get true square footage.
The vertical distance a roof climbs over a given horizontal distance. Combined with run to calculate pitch.
The horizontal distance covered by a roof slope, measured from the outer wall to the point directly beneath the ridge.
Another way to express roof steepness, as rise over run. Often used interchangeably with pitch in the field, though in strict carpentry terms, pitch is rise over total span.
The horizontal distance between the outer walls supporting the roof. Equal to twice the run on a symmetrical gable roof.
The standard unit of roof area: 100 square feet. A 2,500-square-foot roof is 25 squares. Materials, labor, and insurance estimates are all priced per square.
An added labor cost for roofs above a certain pitch, often 7:12 or 8:12 and up, where crews need roof jacks, harnesses, and more time. Some contractors also add charges for second- and third-story work.
The process of calculating every material and quantity a job requires from measurements or plans. Includes shingles, underlayment, flashing, vents, fasteners, and accessories.
The extra materials ordered to cover cuts, overlaps, and mistakes. Simple gable roofs often run around 10%. Hip and cut-up roofs with lots of valleys and dormers commonly run 15% or more.
A small peaked structure built on the high side of a chimney to divert water and debris around it. Also called a saddle. The IRC requires one when the chimney's dimension parallel to the ridge is greater than 30 inches, unless the chimney intersects the ridge.
The cap installed on top of a parapet wall to keep water out of the wall cavity. Usually metal, sloped to drain toward the roof.
Flashing embedded in or attached to a wall or chimney that overlaps the base or step flashing below it. Its job is to cover the top edge of the lower flashing so water can't get behind it.
The structural surface the roof covering is installed on, usually plywood or OSB panels on residential roofs. Also called sheathing. Rotted or delaminated decking is replaced during a tear-off and is a common line item on change orders.
A structure projecting from a sloped roof, usually containing a window. Adds headroom and light to attic spaces. Each dormer adds valleys, step flashing, and labor to a job.
The vertical pipe that carries water from the gutter to the ground or a drainage system. Undersized or clogged downspouts cause gutters to overflow and water to back up under the roof edge.
L-shaped metal flashing installed along the eaves and rakes. Directs water off the roof edge into the gutter and away from the fascia. Required by the IRC for asphalt shingle roofs.
The lower edge of the roof that overhangs the exterior wall. Eaves are where gutters attach and where ice dams form in cold climates.
A raised, flashed frame that supports rooftop equipment, such as a rooftop HVAC unit, above the roof surface. Poorly flashed curbs are a common source of commercial roof leaks.
The vertical board running along the roof edge at the eaves, where gutters are mounted. Rotted fascia is often discovered during a roof replacement.
Thin metal or membrane material used to seal joints and transitions where water could get in: walls, chimneys, valleys, skylights, and penetrations. Most roof leaks trace back to flashing, not to the field of the roof.
The triangular section of wall between the edges of a sloped roof. The roof edge above it is the rake.
A channel installed along the eaves to collect runoff and send it to downspouts. Common materials include aluminum, steel, vinyl, and copper.
The external angle formed where two sloped roof planes meet. Covered with hip and ridge cap shingles.
A piece of flashing installed at the bottom of a roof-to-wall intersection that diverts water into the gutter instead of down the wall. Missing kickout flashing is a leading cause of hidden wall rot.
A low wall extending above the roofline, common on flat and low-slope commercial buildings. Needs coping on top and proper flashing at the base.
Any object that passes through the roof surface: vent pipes, exhaust fans, skylights, chimneys, satellite mounts, and solar racking. Every penetration is a potential leak point.
A flashing collar, often rubber over a metal or plastic base, that seals around plumbing vent pipes. The rubber cracks with UV exposure and often fails long before the shingles around it.
One of the sloped structural members that support the roof deck, running from the ridge to the eaves. Common in older and custom-framed homes.
The sloped edge of a roof at the gable end. Rake edges get drip edge and sometimes a rake trim or starter course for wind resistance.
The horizontal peak where two sloping roof planes meet at the top. Usually the location of the ridge vent.
Specially shaped shingles or pieces installed over the ridge and hips to seal the joint. Manufacturers sell matching ridge cap products, which are often required for enhanced system warranty coverage.
An opening in a parapet wall that lets water drain off a flat or low-slope roof. Often paired with a collector box and downspout.
A window installed in the roof plane. Needs dedicated flashing kits. Older skylights are often replaced during reroofing since flashing them twice costs more than replacing once.
The finished underside of the roof overhang, between the fascia and the exterior wall. Vented soffits are the most common source of intake ventilation.
Individual L-shaped flashing pieces woven in with each shingle course where a roof meets a vertical wall. Each piece overlaps the one below it to shed water down and out.
A prefabricated triangular framing unit that supports the roof, built from smaller lumber joined with metal plates. Standard on most new homes. Trusses should never be cut or modified without engineering approval.
The internal angle where two roof planes meet and water converges. Valleys carry more water than any other part of the roof and are installed open, closed-cut, or woven.
A steep roof whose two sides run nearly to the ground, forming a triangle that serves as both roof and walls. Common on cabins and vacation homes. The large surface area means more material per square foot of living space than most designs.
A hip roof variation with two slopes on each side, where the lower slope is shallower and flares out over the walls. Often covers a porch. The break between slopes needs careful flashing to stay watertight.
A V-shaped roof made of two surfaces that slope inward toward a central valley. Popular in modern architecture and useful for rainwater collection. The center valley handles all runoff, so drainage design and waterproofing are critical.
A roof with a vertical wall of windows set between two roof levels, bringing natural light into the interior. The wall-to-roof intersections create extra flashing points that need regular inspection.
Any roof that mixes two or more styles, such as a hip roof with gable dormers. Common on larger custom homes. More intersections mean more valleys, more flashing, and a higher waste factor on the estimate.
Two or more gable sections joined at right angles, typical on L-shaped and T-shaped homes. The intersections form valleys that are frequent leak points.
A hip roof topped with a small gable section at the ridge. Also called a gablet roof. It adds attic space and ventilation options compared to a standard hip roof.
A roof with little or no visible slope, though most "flat" roofs carry a slight pitch (often around 1/4 inch per foot) for drainage. Standard on commercial buildings. Usually covered with single-ply membranes, modified bitumen, or built-up roofing rather than shingles.
The classic triangular roof: two sloping sides meeting at a ridge, with vertical gable ends. Simple to frame and shingle, and sheds water and snow well. Gable ends can be vulnerable to wind uplift in high-wind regions.
A two-sided roof with two slopes per side, the lower one much steeper than the upper. The classic barn roof. Creates usable upper-floor space but takes heavy snow and wind loads at the slope break.
A roof system covered with vegetation and growing medium over a waterproof membrane and root barrier. Also called a living roof. Requires structural review for the added weight and specialized drainage layers.
A roof with slopes on all four sides that meet at a ridge or a single point. Hip roofs handle wind better than gable roofs, which makes them common in hurricane-prone areas. Hips and ridges need cap shingles along every edge.
A roof with a pitch of 3:12 or less, the range where water drains slowly enough that standard shingles become risky. Most shingle manufacturers and the IRC require extra underlayment below 4:12 and prohibit asphalt shingles below 2:12. Membranes are the usual choice here.
A four-sided roof with two slopes per side, the lower one nearly vertical and often fitted with dormer windows. Common on French-influenced and historic buildings. The steep lower section is often treated more like a wall for material choices.
A hip roof where all four sides meet at a single peak, with no ridge. Common on small square structures like garages, gazebos, and pool houses.
An asymmetrical gable roof with one side much longer and lower than the other. A New England colonial staple. The long slope is typically the rear of the house.
A series of parallel ridges, each with one steep or vertical glazed face and one sloped face, resembling saw teeth. Used on factories and warehouses to bring in daylight. Each valley between teeth needs drainage attention.
A single sloped plane, also called a skillion or lean-to roof. Common on additions, porches, and modern homes. Easy to build, but the low end must handle all runoff.
A roof with a pitch above 3:12, which is NRCA's dividing line between low-slope and steep-slope. Steep enough for water-shedding materials like shingles, tile, slate, and metal panels. Most residential roofing work is steep-slope. Pitches above 7:12 or 8:12 usually trigger steep charges and extra fall protection.
Asphalt shingles made from two or more laminated layers, giving a thicker, dimensional look. Also called laminated or dimensional shingles. They weigh more than three-tab shingles, carry higher wind ratings, and typically come with longer manufacturer warranties.
Shingles made from a fiberglass mat coated in asphalt and surfaced with ceramic-coated mineral granules. The most common residential roofing material in the U.S., and a big part of the roofing industry trends shaping contractor demand. Typical service life runs from about 15 to 30 years depending on product line, climate, and ventilation. Some product lines carry "lifetime" limited warranties, but warranty length is not the same as service life. The Asphalt Roofing Manufacturers Association (ARMA) publishes installation and technical guidance.
A low-slope system made from alternating layers of bitumen and reinforcing felts, finished with gravel or a mineral cap sheet. One of the oldest commercial systems. Durable and redundant, but heavy and labor-intensive to install.
Kiln-fired clay tiles in barrel, flat, or interlocking profiles. Common in Spanish, Mediterranean, and Southwestern architecture. Long-lived and fire-resistant, but heavy and brittle, so the structure must be checked before installation and walking on it takes care. The Tile Roofing Industry Alliance publishes installation manuals for clay and concrete tile.
Molded tiles made from sand, cement, and water, often styled to look like clay, slate, or wood. Less expensive than clay and widely used in Florida, California, and the Southwest. Heavy, so framing must be rated for the load.
A roof surface designed to reflect more sunlight and release absorbed heat faster than standard materials. Achieved with reflective membranes, coatings, or specially rated shingles and tiles. The U.S. Department of Energy notes cool roofs can lower roof surface temperatures and cooling loads. Some jurisdictions, including California under Title 24, require cool roof products for certain projects.
Premium metal roofing made from copper sheets or shingles, often used for accents like bay windows, cupolas, and porches. Develops a green patina over time. Can last for generations, but material cost is far higher than other metals.
Ethylene propylene diene monomer. A synthetic rubber single-ply membrane, usually black, used on low-slope and flat roofs. Installed fully adhered, mechanically attached, or ballasted, with seams joined by tape or adhesive. SPRI, the single-ply roofing industry association, develops design standards for EPDM, TPO, and PVC systems.
Metal panels attached with screws driven through the panel face, sealed with rubber washers. Corrugated and R-panel are common profiles. Cheaper and faster to install than standing seam, but the washers degrade over time and need periodic inspection.
Shingles built to withstand hail, usually tested to UL 2218 and rated Class 4 at the top end. Often made with SBS-modified asphalt or reinforced backing. Many insurers in hail-prone states offer premium discounts for Class 4 roofs, which makes them an easy upsell in storm markets.
Asphalt modified with polymers and reinforced with fiberglass or polyester, sold in rolls for low-slope roofs. APP-modified sheets are typically torch-applied. SBS-modified sheets can be hot-mopped, cold-adhered, or self-adhered.
A single-ply thermoplastic membrane with heat-welded seams. Resists chemicals, grease, and fire, which makes it common on restaurants and industrial roofs. Usually white and reflective.
A liquid-applied layer (acrylic, silicone, polyurethane, or similar) rolled or sprayed over an existing roof to waterproof, reflect heat, or extend service life. Works best on roofs that are structurally sound with limited saturated insulation.
Natural stone split into thin tiles. One of the longest-lasting roofing materials available, with quality slate capable of lasting a century or more. Heavy, expensive, and requires installers trained in slate-specific techniques and repairs.
Roofing shingles or tiles with built-in photovoltaic cells that generate electricity while serving as the roof covering. Installation often requires coordination with electrical contractors and utility interconnection approval.
A two-part foam sprayed as a liquid that expands into a seamless, insulating roof layer. Usually topped with a protective coating. Common on commercial low-slope roofs with lots of penetrations. The Spray Polyurethane Foam Alliance runs certification programs for SPF applicators.
Metal panels joined by raised, interlocking seams, with fasteners hidden beneath the panels. Allows the metal to expand and contract with temperature. A premium residential and commercial option with long service life and strong wind performance. The Metal Roofing Alliance offers resources on metal systems.
Steel panels coated with stone granules bonded in acrylic, styled to look like shingles, shakes, or tile. Lighter than tile and highly resistant to wind and hail.
Shingles made from engineered polymers or rubber blends, designed to mimic slate or cedar shake. Lighter than the materials they imitate and typically carry high impact and fire ratings.
A woven or spunbond polymer underlayment that has largely replaced felt on residential roofs. Lighter, stronger, more tear-resistant, and safer to walk on than felt.
Single-layer asphalt shingles with cutouts that create three flat tabs per strip. Once the residential standard, now mostly used for budget jobs, outbuildings, and starter strips. Thinner and lower wind-rated than architectural shingles.
Thermoplastic polyolefin. A single-ply membrane, usually white, with seams joined by hot-air welding. One of the most widely installed commercial roofing membranes thanks to its reflectivity and cost.
The water-resistant layer installed over the decking and beneath the roof covering. Acts as a secondary barrier if water gets past the shingles. Traditionally asphalt-saturated felt, now mostly synthetic.
Roofing made from split or sawn wood, usually cedar. Shakes are hand-split, thicker, and rougher. Shingles are machine-sawn, thinner, and more uniform. Both need ventilation and maintenance, and untreated wood may not meet fire codes in wildfire-prone areas. The Cedar Shake & Shingle Bureau sets grading and installation standards.
The continuous flow of air through the attic, drawn in low at the eaves and exhausted high near the ridge. Keeps heat and moisture from building up, which protects shingles, decking, and insulation. Poor ventilation can void some shingle warranties.
A setup where intake and exhaust ventilation are roughly equal, so air moves evenly through the attic. The IRC generally calls for 1 square foot of net free vent area per 150 square feet of attic floor, reducible to 1 per 300 when certain conditions like balanced upper and lower vents are met. Check local code.
A static exhaust vent installed near the ridge, also called a turtle vent or louver vent. Works by convection with no moving parts. Several are typically needed to equal one continuous ridge vent.
Water that forms when warm, moist indoor air reaches a cold surface like the underside of the roof deck. Shows up as frost, dripping, or mold in the attic. Usually a ventilation or air-sealing problem, not a roof leak.
Any vent that lets hot, moist air escape from the upper attic. Includes ridge vents, box vents, turbine vents, and power fans. Mixing different exhaust types on the same roof can short-circuit airflow.
A louvered vent installed in the gable wall. Common on older homes. Can interfere with ridge vent airflow when the two are used together.
A ridge of ice that forms at the eaves when heat from the house melts snow higher on the roof and the water refreezes at the colder overhang. Water pools behind the dam and backs up under shingles. In areas with a history of ice damming, the IRC requires an ice barrier from the eave to at least 24 inches inside the exterior wall line.
A vent that lets cool outside air into the lower attic, usually through the soffits or along the drip edge. Without enough intake, exhaust vents can't do their job.
The actual open area of a vent that air can pass through, after subtracting screens, louvers, and baffles. Manufacturers list NFA in square inches. Used to calculate how many vents a roof needs.
An electric or solar fan mounted on the roof or gable that actively exhausts attic air. Can pull conditioned air from the house through ceiling gaps if the attic lacks enough intake.
A channel installed between rafters at the eaves that keeps insulation from blocking soffit vents. Also called a vent chute or insulation baffle.
A continuous exhaust vent installed along the ridge and covered with ridge cap shingles. The most common exhaust ventilation on modern residential roofs. Needs balanced intake to work.
Perforated or slotted panels in the soffit that serve as the primary intake vent on most homes. Can be continuous strips or individual rectangular vents.
A wind-driven exhaust vent with spinning vanes that pull air out of the attic. Also called a whirlybird. Effective in windy areas but has moving parts that can wear and squeak.
A layer that slows moisture from moving out of the building into the roof assembly. Common in commercial low-slope roofs in cold climates and over high-humidity spaces like pools.
No terms or definitions match your search.
Know the terminology. Talk shop with confidence. Explore our other industry-specific glossaries for definitions you can put to work in the field, at the kitchen table, and across every part of your business.
A complete reference for heating, ventilation, air conditioning, and refrigeration terms, from compressor types to refrigerant regulations.
Clear definitions of the financial terms contractors use every day, from APR and prequalification to promotional financing and dealer fees.
Disclaimer: Finturf is not a lender. Finturf does not make loans, approve credit, or provide financial, legal, tax, or lending advice. The definitions in this glossary are for general educational purposes only. Laws and lender programs change over time. Financing offered through Finturf is provided by third-party lenders and is subject to credit approval and each lender’s terms. Review the lender’s disclosures and consult a qualified professional before making financing decisions.